Advertisements
Archives

voyage

This tag is associated with 58 posts

Sail Care, Interview with an Expert – Article in SpinSheet Magazine

Amelia’s article, Sail Care, Interview with an Expert, appears in the April issue of SpinSheet magazine.  Grant worked as a sail inspector for two years at Bacon Sails and Marine Supplies in Annapolis, MD.  Here are some of his tips on Sail Care!!

Click here to read the entire April 2014 issue of SpinSheet magazine!

And, read our blog post on designing Albin Vega Velocir‘s Sail Design.

Interested in what we’ve been up to?  Stay tuned next week for an exciting update, it’ll be something a little different…

Velocir Sail Care Article in SpinSheet

Advertisements

Co-Captaining,Can It Be Done? – Article in SpinSheet Magazine!

Amelia’s article, Co-Captaining – Can It Be Done?, appears in the April issue of SpinSheet magazine.  We co-captain Velocir, which is probably not typical of most boating couples.  Happy to say it worked very well for us during our entire voyage– below is the article giving more insight.

Click here to read the entire April 2013 issue of SpinSheet magazine!

ssss

Capture

I’m On A Boat–Interior Paint Preparation

Let’s go back in time, to when Velocir was completely stripped down to a bare hull.  Yes, that glorious moment when the interior was saying “paint me, I have no wood in me and am already a filthy dust pile!”  But no one heard the calls.

Fast forward to cruising Velocir and the paint is porous, crumbly and very susceptible to mold.  If only we had realized!!  Of course, that would have made things easy….

Albin Vega Velocir Interior Paint Preparation

There are two reasons why the interior desperately needs to be painted—mold and flaking paint.  Why is this happening—this is caused mostly by A) porous old paint on a bumpy fiberglass surface B) a gel-coat like filler was used along the outer 1-2 inches of the hull right where the deck meets the hull.  This filler has flex cracks, or in some cases just crumbly texture, causing a mold habitat.  As the cracks held moisture the paint started to flake and fall off.  The paint is not adhering to the filler at all anymore.

Albin Vega Velocir Interior Paint Preparation

To solve this problem Amelia is going to tackle this pain of a project.  It is a pain because A) you have to be a gymnast to work upside down in these cramped conditions B) it is messy, mess everywhere all over our home C) the wood paneling limits access to the far reaches of some areas and gives little to no clearance to paint between wood bulkheads and the fiberglass.  It is a delicate process to do the job well, without focusing on all the imperfections that will inevitably happen.

Albin Vega Velocir Interior Paint Preparation

Beginning with the nice vision of a fresh, bright and clean Velocir in mind, Amelia first took out any hardware that needed to be removed for sanding and duct taped a plastic sheet to keep dust out of the main cabin.  Then, using a rotary sander with 80 grit and a little “mouse” sander with 120 grit, she sanded the surfaces thoroughly.  Around the edges of the hull where the paint was flaking, she used a chisel, and then hand sanded the surface.

Albin Vega Velocir Interior Paint Preparation

About halfway into the project Amelia started to regret the undertaking.  Dust everywhere, sanding in corners, upside down, around windows and other obstacles.  Her arms started to feel weak from pushing the sander against the hull.  What a mess the boat was!  But it was too late to turn back now.

Albin Vega Velocir Interior Paint Preparation

The interior was now sanded and smooth, but very dusty.  Amelia used a shop vac to get most of the grime off every surface.  Then, she used diluted bleach water and wiped down every surface.  Some mold still hid in sanded areas, so this really cleaned things up!

Albin Vega Velocir Interior Paint Preparation

The duct taped plastic shield worked great!  It didn’t stick to the varnished wood or leave any residue.

Albin Vega Velocir Interior Paint Preparation

On outer edges of the hull, an epoxy-like filler was used.  This is where the flex cracks happened.  Using a dremel, Amelia gouged out the cracks until they were smooth.  There were also crumbly areas that were cleaned out.  Most cracks were superficial, but two (by the water tank input, and by the starboard lifeline stanchion) were 1/8” deep.

Albin Vega Velocir Interior Paint Preparation

To fill these cracks we needed something that a latex based paint would adhere to.  It also could not be too rigid or else it would crack again.  Our solution was g-flex, a flexible epoxy that we used to repair our inflatable dinghy’s oar locks in the Bahamas with great success.  It is easy to mix the 1:1 solution and apply.  The application was very simple because it did not want to move around, even when applying upside down.  At times (probably because it was so cold) it got stringy but was manageable.

Albin Vega Velocir Interior Paint Preparation

Once the epoxy cures it will be sanded, wiped down with acetone and the entire forward interior will be ready to paint.  First we will use a primer, then glossy paint.  Hopefully the weather will warm up for that project soon!

I’m On A Boat- Solar Vent Installation

Before leaving on our trip to the Bahamas in 2011, we installed new solar vents on Velocir.  We had seen many older solar vents in boat yards still going strong after many years and much neglect.

The original installation required us to enlarge pre-existing 3 inch vents holes to 4 inches.  We epoxied the cored deck so that it would be water tight, and installed the vent.  It was great except that in heavy weather (crashing waves and spray) it would leak a bit., otherwise we love them!  This summer our starboard vent stopped working, so we replaced it:

Solar Vent Installation by Velocir

After taking the old vent out we waited a few weeks for a new one (free under warranty) to come in the mail.  Then, Amelia installed it by lightly chiseling off the old foam ring and Dolfinite sealing compound.  Mineral Spirits and kerosene also work really well at getting Dolfinite off.

Solar Vent Installation by Velocir

There are three main pieces to install.  The base (top right), the white ring is the interior trim piece, the foam ring is part of the waterproof bedding on deck, and then the cover piece with the solar panel and motor.  Since we already had holes drilled it was super easy to install.  (Note: Before drilling holes, make sure your vents have solar panels aesthetically going the way you like.)

Solar Vent Installation by Velocir

We put fresh bedding compound, Dolfinite, down before installing the base.  Contrary to what you might assume, Amelia doesn’t just use Dolfinite because there is a cute dolphin on the label.  The other advantages are that with age, the bedding compound is still easy to remove and reapply.  It doesn’t easily dry out under basic storage methods.  (It is messy to apply though, comically so, like peanut butter).

Solar Vent Installation by Velocir

The base fit right in.  The white part of the base slides up and down, allowing air in/out or cutting it off.  There is also a handy bug screen.

Solar Vent Installation by Velocir

And, Viola!  A beautiful new and working solar vent.  Aren’t warranties great?

P.S.  They are very quiet.  Every once in a while one will start to make a ticking sound, so we restart and silence again : )

CANCELLED –The Great Lakes – Summer 2013

We are excited to announce that we have finally fully committed to sailing the Great Lakes on Velocir this summer.

We were unsure throughout the winter, trying to find long-term work, but that didn’t pan out so we are back and focused on cruising and Velocir.

Velocir

This past winter was well spent enjoying the comforts of a home and raising a delightful dog.  We really couldn’t be happier with Crew, he’s just the sweetest little guy.  But despite our best efforts, he doesn’t like water—yet. So it should be an interesting summer for him!

Crew by Velocir

We plan to depart in late April / early May and head through various canals for Georgian Bay and the North Channel. Most likely (unless we win the lottery) this will be the last hurrah of cruising for us, so we plan to just have a nice time and enjoy it!

I’m On A Boat–Downsizing Your Sailboat

Before Motu Iti, Amelia’s parents had cruised and sailed two other bigger 40 foot sailboats.  One cruise was to the Bahamas for a year with a young family, the others summer cruises as a couple and with a young family.

Tiny Motu Iti

They chose Motu Iti because her smaller size makes her easier to handle and take care of.  Here is a video discussing the best aspects of downsizing to a smaller sailboat!!  And, see Motu Iti’s blog on the topic here.

I’m On A Boat–Using a Nature’s Head

The Nature’s Head Composting Toilet has been a great solution to rid ourselves of stinky holding tanks, repairing valves and finding pump-outs.  Even better, being ecologically friendly on the boat has become effortless for us.

In Georgetown, Bahamas, the pump-out boat went through Elizabeth Harbor every morning, $5 for a pump out.  We thought, I hope he doesn’t notice we don’t need one, because we have the Nature’s Head.  The pump-out guy would get angry on the VHF radio when he wasn’t getting a lot of business, saying outrageous things like “you cruiser’s must like to swim in your own discharge” and various such proclamations.  We thought, how rude, I hope he realizes people have composting heads  now and are considerate to others.

Then, we were blown away when we met two other cruising boats openly proud of their complete disregard for proper discharge, in a crowded cruiser’s harbor too!  Like it was an inside joke they were letting us in on and they were such rebels.

But really it was disgusting and inconsiderate, and there is no excuse, none, especially with a Nature’s Head.  Part of the reason we love to cruise is to be outside and enjoy nature, so even if it’s just something small like our discharge,  we take pride in doing what we can to protect the sea!

Here’s a video from Motu Iti about using a Nature’s Head:

I’m On A Boat–Creating a Cozy Boat Home

It can take a lot of creativity and hard work to make the interior space of a boat warm and inviting.  Aboard Motu Iti, Nancy shows what she did to make the boat feel like home:

Happy Birthday to Grant!!–and other adventures

Sometimes we wonder why so many people, us included, live in places that are so dreary and cold a good chunk of the year. We are reminded of this every time we use Grant’s birthday as an excuse to visit a tropical locale. Three years running. Last year was on Velocir in Spanish Wells, Eleuthera.

by Velocir

We made a delicious turtle cake, making do with whatever baking pans were available.

by Velocir

For dinner, we skipped the sunset cruiser’s raft-up to enjoy some fine dining. We watched the sunset and the moonrise about 30 minutes apart.

Besides birthday celebrations, we’ve been reading, knitting, snorkeling and walking the beach.  Relaxing in the Caribbean!

by Velocirby Velocirby Velocir

We stopped our lazy ways and got to work, taking Motu Iti out for a sail!  The forecast was 10-15 kts with light chop.  Sailing the Sea of Abaco, Motu Iti did a fine job gliding through the water, not wanting to heel too much even with some puffs.

by Velocir

At the end of our sail, Amelia got in the dinghy and anchored it, while Motu Iti sailed back and forth to get some great photos.

by Velocir

It’s hard to have good sailing pictures of your boat when you’re always on it!

Here’s some fun video of the sail:

Bon Voyage to MOTU ITI!

motuiti

We are excited to share with everyone that MOTU ITI has officially left on their cruise this winter.  After a lot of work and planning, their cruising dreams have become a reality.  They were the boat we featured in our “I’m On A Boat” Youtube series.

Their small sailboat is a Camper Nicholson 31.  Check out their blog at www.sailmotuiti.com!

motu iti2

Advertisements

Watch Our Youtube Videos

Calendar

December 2017
S M T W T F S
« Nov    
 12
3456789
10111213141516
17181920212223
24252627282930
31  

Archives

Categories